HELLO & WELCOME
JustGlazedUnits is a Double Glazed Glass Unit Replacement Service for Hampshire and the surrounding areas.
Replacing (broken/misted-up/condensation) old sealed units in uPVC/Aluminium windows and doors.
I supply and fit –
Clear or Obscure double glazed units using Float Glass/Toughened Glass, rated A or C with or without Georgian Bars or Lead designs plus cut-outs for Cat/Dog flaps.
Fitting them into –
PVC/Aluminium Composite Doors, Residential Doors, French Doors, Patio Doors, Bi-Folding Doors and Windows.
** FREE quotation with NO minimum order **
I’ve been fitting windows, doors and conservatories for over 10 years and have worked for some of the big companies here in the south.
I set up my own installation company to give my customers great service from start to finish, something I feel these bigger companies struggle to give.
Since then, the feedback that I have received from my customers has made the move from working for a big company to working for myself, all the worthwhile.
You can read my reviews on – Yell.com, MyBuilder.com & Cheackatrade.com
Condensation is not caused by double glazing
(although new windows can sometimes make a condensation problem worse, by cutting out draughts).
Condensation on the inside of sealed units
Condensation happens when water vapour in the air changes to liquid water. There can be many causes but put simply it generally occurs in the atmosphere when warm air rises, as it cools down it loses its capacity to hold water vapour. Water vapour then condenses on cool surfaces to form liquid water which is why often you will see windows with condensation on them.
Treatment for condensation is ventilation (to vent moisture-bearing air to the outside) and heating (to raise surfaces above dew point temperature).
Condensation on the outside of sealed units
External condensation (dew) can occasionally occur on highly insulating glass units in temperate climates. Such occurrences will only happen on cloud-free nights when there is little or no wind and usually when a warm front follows a dry spell.
With modern Low E Glass products more of the heat is kept inside and the outer pane is not heated as much. Moisture condenses out of the air onto a cold surface that is said to be below the dew point.
In short, the “problem” is caused by the fact that the Low E Glass is doing its job so well and reflecting heat back into the room that there is nothing to worry about if you see external condensation on your new double glazed windows.
Condensation between both glazed panels
If you find condensation/moisture inside your glass, then the sealed unit itself has broken down and has started pulling in moisture.
This may be because the unit is old (over time it has broken down) and will need to be replaced or if the sealed unit is new, then the seal around the unit was just not sealed off properly in the factory and has started pulling in moisture.
This is now the time to replace your units.
CAT & DOG FLAP INFORMATION
Panel Cut Outs
Adding any size flap into a door panel is as simple as turning up and cutting out the hole and installing the flap.
If the flap is going into an existing panel, then this is a charged at £40 per cut-out and install.
If a new panel is needed then I would need to get a quote for a new panel from my supplier and this would then be added to the £40 install charge.
Glass Cut Outs
Getting a cat flap hole put into a double glazed unit isn’t as straightforward as turning up and cutting out a hole.
You would need to start from scratch and have a new double glazed unit made to measure with the right size cut-out.
This will be a new sealed unit with the same spacerbar used for the sides of the glass around the cut-out. (see picture).
Double Glazed Glass Unit Replacement Service for Hampshire and the surrounding areas.
Please Note –
Depending on how far you are outside of Hampshire, mileage costs maybe added.
I DO NOT service the Isle of Wight, Sorry.
YOU CAN CONTACT ME ON – 07738355700
HOW TO GET IN CONTACT.
You can contact me on 07738355700, firstname.lastname@example.org or by using the form below.